Subject: Re: [baidarka] New boat photos, and seat question
From: Mark Reuten (clinker@look.ca)
Date: Fri Oct 26 2001 - 10:30:43 EDT
Feathercraft makes a seat something like that for their Kahtsilano model
(greenland model) It is the only one I've found that is low enough to fit
in a greenland kayak and enadble rolling. That said, I've gon back to a
simple back band and thermorest seat.
Mark Reuten
www.nomadboatbuilding.com
----- Original Message -----
From: "Cicotello, Gina" <GCicotello@finsys.com>
To: "Baidarka List (E-mail)" <baidarka@paddlewise.net>
Sent: Wednesday, October 24, 2001 1:26 PM
Subject: [baidarka] New boat photos, and seat question
> (Aaah, ain't it good to see a new thread starting...)
>
>
> Hi folks,
>
> No official launch yet, but let me introduce another new boat to the
scene.
>
> Photos at http://photos.yahoo.com/gcicotello (mostly construction pics)
> Apologies for the few fuzzy shots, my little PHD camera doesn't do
close-ups very well.
>
> I built her with Bruce Lemon in Seneca Lake NY, the last week in September
2001. Remember, I was the one trying to track him down awhile back. Bruce
> is alive and well, living in a gorgeous waterfront spot in the
Adirondacks, and teaching on an individual basis only. I had a spectacular
week up
> there, and we worked fast enough to allow me some time for bike riding and
winery hopping.
>
> The boat is 17' long, 22" wide. Standard Bruce Lemon kit of douglas fir,
white oak, yellow pine, and spruce. I've finished the gazillion coats of
> Dura-Tuff and it looks beautiful; all it needs is some deck rigging (holes
were pre-drilled in the gunwales, just have to get cord) and the seating
> arrangement.
>
> Speaking of working out my seating arrangement...
>
> Bruce showed me one of his boats with a seat I'd like to duplicate, but
can't find. The seat was very thin (1/4" thick, if that) and small,
basically
> a layer of foam covered in nylon, with straps attached. Low profile in
the back to allow rolling, but unlike the typical back straps it extended
down
> under the paddler's butt for a little extra motion stability and
cushioning.
>
> Anyone know what this seat is, and if it's commercially available? I
could try sewing one myself, but buying it might get me launched quicker.
>
> Interesting - He had actually cut two holes in the bottom of the seat,
under the paddler's sit-bones. It got you slightly lower in the cockpit,
and
> allowed a bracing point. Very comfortable. I've seen many rowing seats
(even hard wooden ones) made that way.
>
> The seat was placed over a flat, thin, closed-cell foam pad that covered
the floor boards all the way forward to underneath the paddler's feet. That
> piece I can scrounge or make with no problem.
>
> Comments, suggestions welcomed!
> - Gina
>
> -
> Baidarka Mailing List - All postings copyright the author and not to be
> reproduced outside Baidarka or Baidarka archives without author's
permission
> Submissions: baidarka@paddlewise.net
> Subscriptions: baidarka-request@paddlewise.net
> Searchable archive: http://rtpnet.org/robroy/baidarka
>
>
-
Baidarka Mailing List - All postings copyright the author and not to be
reproduced outside Baidarka or Baidarka archives without author's permission
Submissions: baidarka@paddlewise.net
Subscriptions: baidarka-request@paddlewise.net
Searchable archive: http://rtpnet.org/robroy/baidarka
This archive was generated by hypermail 2b27 : Thu Nov 01 2001 - 01:30:04 EST